0755-23179541 
sales@oyii.net
Anchoring Clamp PA3000
Hardware Products Overhead Line Fittings
Anchoring Clamp PA3000
Product Description
The anchoring cable clamp PA3000 is of high quality and durable. This product consists of two parts: a stainless-steel wire and its main material, a reinforced nylon body that is lightweight and convenient to carry outdoors. The clamp's body material is UV plastic, which is friendly and safe and can be used in tropical environments and is hung and pulled by electroplating steel wire or 201 304 stainless-steel wire. The FTTH anchor clamp is designed to fit various ADSS cable designs and can hold cables with diameters of 8-17mm. It is used on dead-end fiber optic cables. Installing the FTTH drop cable fitting is easy, but preparation of the optical cable is required before attaching it. The open hook self-locking construction makes installation on fiber poles easier. The anchor FTTX optical fiber clamp and drop wire cable brackets are available either separately or together as an assembly.
FTTX drop cable anchor clamps have passed tensile tests and have been tested in temperatures ranging from -40 to 60 degrees Celsius. They have also undergone temperature cycling tests, aging tests, and corrosion-resistant tests.
Product Features
1.Good anti-corrosion performance.
2.Abrasion and wear resistant.
3.Maintenance-free.
4.Strong grip to prevent the cable from slipping.
5.Body is cast of nylon body, it’s lightly and convenient to carry outside.
6.SS201/SS304 Stainless steel wire has guaranteed firm tensile force.
7.Wedges are made of weather resistant material.
8.The installation does not require any specific tools and the operating time is drastically reduced.
Specifications
|
Model |
Cable Diameter (mm) |
Break Load (km) |
Material |
Warranty Time |
|
OYI-PA3000A |
8-12 |
5 |
PA, Stainless Steel |
10 Years |
|
OYI-PA3000B |
13-17 |
5 |
PA, Stainless Steel |
10 Years |
Installation Instructions
Anchoring clamps for ADSS cables installed on short spans (100 m max.)
Attach the clamp to the pole bracket using its flexible bail.
Push on the wedges by hand to initiate the gripping onto the cable.
Place the clamp body over the cable with the wedges in their back position.
Check the correct positioning of the cable between the wedges.
When the cable is brought to its installation load at the end pole, the wedges move further into the clamp body.
When installing a double dead-end leave some extra length of cable between the two clamps.
Applications
1.Hanging cable.
2.Propose a fitting covering installation situations on poles.
3.Power and overhead line accessories.
4.FTTH fiber optic aerial cable.
Packaging Information
Quantity: 50pcs/Outer box.
1.Carton Size: 50X36X35cm.
2.N. Weight: 23kg/Outer Carton.
3.G. Weight: 23.5kg/Outer Carton.
4.OEM service available for mass quantity, can print logo on cartons.
Inner Packaging
Outer Carton
-
Anchoring Clamp PA600
The anchoring cable clamp PA600 is a high-quality and durable product. It consists of two parts: a stainless-steel wire and a reinforced nylon body made of plastic. The body of the clamp is made of UV plastic, which is friendly and safe to use even in tropical environments. The FTTH anchor clamp is designed to fit various ADSS cable designs and can hold cables with diameters of 3-9mm. It is used on dead-end fiber optic cables. Installing the FTTH drop cable fitting is easy, but preparation of the optical cable is required before attaching it. The open hook self-locking construction makes installation on fiber poles easier. The anchor FTTX optical fiber clamp and drop wire cable brackets are available either separately or together as an assembly.
FTTX drop cable anchor clamps have passed tensile tests and have been tested in temperatures ranging from -40 to 60 degrees. They have also undergone temperature cycling tests, aging tests, and corrosion-resistant tests.
-
Module OYI-1L311xF
OYI-1L311xF Small Form Factor Pluggable (SFP) transceivers are compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA), The transceiver consists of five sections: the LD driver, the limiting amplifier, the digital diagnostic monitor, the FP laser and the PIN photo-detector, the module data link up to 10km in 9/125um single mode fiber.
The optical output can be disabled by a TTL logic high-level input of Tx Disable, and the system also 02 can disable the module via I2C. Tx Fault is provided to indicate that degradation of the laser. Loss of signal (LOS) output is provided to indicate the loss of an input optical signal of receiver or the link status with partner. The system can also get the LOS (or Link)/Disable/Fault information via I2C register access.
-
Jacket Round Cable
Fiber optic drop cable also called double sheath fiber drop cable is an assembly designed to transfer information by light signal in last mile internet constructions.
Optic drop cables usually consist of one or more fiber cores, reinforced and protected by special materials to have superior physical performance to applied in various applications -
OYI-FAT08 Terminal Box
The 8-core OYI-FAT08A optical terminal box performs in accordance with the industry standard requirements of YD/T2150-2010. It is mainly used in the FTTX access system terminal link. The box is made of high-strength PC, ABS plastic alloy injection molding, which provides good sealing and aging resistance. In addition, it can be hung on the wall outdoors or indoors for installation and use.
-
Anchoring Clamp PAL1000-2000
The PAL series anchoring clamp is durable and useful, and it is very easy to install. It is specially designed for dead-ending cables, providing great support for the cables. The FTTH anchor clamp is designed to fit various ADSS cable designs and can hold cables with diameters of 8-17mm. With its high quality, the clamp plays a huge role in the industry. The anchor clamp’s main materials are aluminum and plastic, which are safe and environmentally friendly. The drop wire cable clamp has a nice appearance with a silver color, and it works great. It is easy to open the bails and fix to the brackets or pigtails. Additionally, it is very convenient to use without the need for tools, saving time.
-
10/100Base-TX Ethernet Port to 100Base-FX Fiber...
MC0101F fiber Ethernet media converter creates a cost-effective Ethernet to fiber link, transparently converting to/ from 10 Base-T or 100 Base-TX Ethernet signals and 100 Base-FX fiber optical signals to extend an Ethernet network connection over a multimode/single mode fiber backbone.
MC0101F fiber Ethernet media converter supports maximum multimode fiber optic cable distance of 2km or a maximum single mode fiber optic cable distance of 120 km, providing a simple solution for connecting 10/100 Base-TX Ethernet networks to remote locations using SC/ST/FC/LC-terminated single mode/multimode fiber, while delivering solid network performance and scalability.
Easy to set-up and install, this compact, value-conscious fast Ethernet media converter features autos witching MDI and MDI-X support on the RJ45 UTP connections as well as manual controls for UTP mode, speed, full and half duplex.
If you're looking for a reliable, high-speed fibre optic cable solution, look no further than OYI. Contact us now to see how we can help you stay connected and take your business to the next level.