0755-23179541 
sales@oyii.net.png)
8618926041961
Anchoring Clamp PA2000
Hardware Products Overhead Line Fittings
Anchoring Clamp PA2000
Product Video
Product Features
Good anti-corrosion performance.
Abrasion and wear resistant.
Maintenance-free.
Strong grip to prevent the cable from slipping.
Body is cast of nylon body, it’s lightly and convenient to carry outside.
Stainless steel wire has guaranteed firm tensile force.
Wedges are made of weather resistant material.
The installation does not require any specific tools and the operating time is drastically reduced.
Specifications
| Model | Cable Diameter (mm) | Break Load (kn) | Material |
| OYI-PA2000 | 11-15 | 8 | PA, Stainless Steel |
Installation Instructions
Anchoring clamps for ADSS cables installed on short spans (100 m max.)
Attach the clamp to the pole bracket using its flexible bail.
Place the clamp body over the cable with the wedges in their back position.
Push on the wedges by hand to initiate the gripping onto the cable.
Check the correct positioning of the cable between the wedges.
When the cable is brought to its installation load at the end pole, the wedges move further into the clamp body.
When installing a double dead-end leave some extra length of cable between the two clamps.
Applications
Hanging cable.
Propose a fitting covering installation situations on poles.
Power and overhead line accessories.
FTTH fiber optic aerial cable.
Packaging Information
Quantity: 50pcs/Outer box.
Carton Size: 55*41*25cm.
N.Weight: 25.5kg/Outer Carton.
G.Weight: 26.5kg/Outer Carton.
OEM service available for mass quantity, can print logo on cartons.
Inner Packaging
Outer Carton
-
OYI-FOSC-D108M
The OYI-FOSC-M8 dome fiber optic splice closure is used in aerial, wall-mounting, and underground applications for the straight-through and branching splice of the fiber cable. Dome splicing closures are excellent protection of fiber optic joints from outdoor environments such as UV, water, and weather, with leak-proof sealing and IP68 protection. -
Loose Tube Armored Flame-retardant Direct Burie...
The fibers are positioned in a loose tube made of PBT. The tubes are filled with a water-resistant filling compound. A steel wire or FRP is located in the center of the core as a metallic strength member. The tubes and the fillers are stranded around the strength member into a compact and circular core. An Aluminum Polyethylene Laminate (APL) or steel tape is applied around the cable core, which is filled with filling compound to protect it from water ingress. Then the cable core is covered with a thin PE inner sheath. After the PSP is longitudinally applied over the inner sheath, the cable is completed with a PE (LSZH) outer sheath.(WITH DOUBLE SHEATHS) -
10/100Base-TX Ethernet Port to 100Base-FX Fiber...
MC0101F fiber Ethernet media converter creates a cost-effective Ethernet to fiber link, transparently converting to/ from 10 Base-T or 100 Base-TX Ethernet signals and 100 Base-FX fiber optical signals to extend an Ethernet network connection over a multimode/single mode fiber backbone.MC0101F fiber Ethernet media converter supports maximum multimode fiber optic cable distance of 2km or a maximum single mode fiber optic cable distance of 120 km, providing a simple solution for connecting 10/100 Base-TX Ethernet networks to remote locations using SC/ST/FC/LC-terminated single mode/multimode fiber, while delivering solid network performance and scalability.Easy to set-up and install, this compact, value-conscious fast Ethernet media converter features autos witching MDI and MDI-X support on the RJ45 UTP connections as well as manual controls for UTP mode, speed, full and half duplex. -
OYI-FOSC-H06
The OYI-FOSC-01H horizontal fiber optic splice closure has two connection ways: direct connection and splitting connection. They are applicable to situations such as overhead, man-well of pipeline, embedded situation, etc. Comparing with a terminal box, the closure requires much stricter requirements of seal. Optical splice closures are used to distribute, splice, and store the outdoor optical cables which enter and exit from the ends of the closure. The closure has 2 entrance ports. The shell of the product is made from ABS+PP material. These closures provide excellent protection for fiber optic joints from outdoor environments such as UV, water, and weather, with leak-proof sealing and IP68 protection. -
Optical Fiber Cable Storage Bracket
The Fiber Cable storage bracket is useful. Its main material is carbon steel. The surface is treated with hot-dipped galvanization, which allows it to be used outdoors for more than 5 years without rusting or experiencing any surface changes. -
ABS Cassette Type Splitter
A fiber optic PLC splitter, also known as a beam splitter, is an integrated waveguide optical power distribution device based on a quartz substrate. It is similar to a coaxial cable transmission system. The optical network system also requires an optical signal to be coupled to the branch distribution. The fiber optic splitter is one of the most important passive devices in the optical fiber link. It is an optical fiber tandem device with many input terminals and many output terminals, especially applicable to a passive optical network (EPON, GPON, BPON, FTTX, FTTH, etc.) to connect the ODF and the terminal equipment and to achieve the branching of the optical signal.
If you're looking for a reliable, high-speed fibre optic cable solution, look no further than OYI. Contact us now to see how we can help you stay connected and take your business to the next level.
