0755-23179541 
sales@oyii.net.png)
8618926041961
GYFXTH-2/4G657A2
Indoor & Outdoor Drop Cable
GYFXTH-2/4G657A2
Product Features
GYFXTH is mainly used for wireless base station horizontal deployment of fiber optic cable, at the same time can be used for integrated cabling in the building introduction cable, suitable for outdoor to indoor introduction of pipeline wiring. The 250μm optical fiber is put into the loose casing made of high modulus material, the loose casing is filled with thixotropic waterproof compound, and glass yarn (or aramid) is added to squeeze a layer of LSZH outer sheath.
Optical Fiber in Cable-G.657A2
Cable Dimensions and Constructions
Mechanical and Environmental Characteristics
Packing
Not allowed two length units of cable in one drum, two ends should be sealed, Two ends should be packed inside drum, reserve length of cable not less than 3 meters.
Delivery Length
Standard delivery length is 2 km/drum. Other length available on request.
-
OYI 321GER
ONU product is the terminal equipment of a series of XPON which comply fully with ITU-G.984.1/2/3/4 standard and meet the energy-saving of G.987.3 protocol, onu is based on mature and stable and high cost-effective GPON technology which adopts high-performance XPON Realtek chipset and has high reliability,easy management,flexible configuration，robustness，good quality service guarantee(Qos). ONU adopts RTL for WIFI application that supports IEEE802.11b/g/n standard at the same time，a WEB system provided simplifies the configuration of the ONU and connects to INTERNET conveniently for users. XPON has G / E PON mutual conversion function, which is realized by pure software. -
LGX Insert Cassette Type Splitter
Fiber optic PLC splitter, also known as a beam splitter, is an integrated waveguide optical power distribution device based on a quartz substrate. It is similar to a coaxial cable transmission system. The optical network system also requires an optical signal to be coupled to the branch distribution. The fiber optic splitter is one of the most important passive devices in the optical fiber link. It is an optical fiber tandem device with many input terminals and many output terminals. It is especially applicable to a passive optical network (EPON, GPON, BPON, FTTX, FTTH, etc.) to connect the ODF and the terminal equipment and to achieve the branching of the optical signal. -
Jacket Round Cable
Fiber optic drop cable, also known as double sheath fiber drop cable, is a specialized assembly utilized for transmitting information via light signals in last – mile internet infrastructure projects. These optic drop cables typically incorporate one or multiple fiber cores. They are reinforced and safeguarded by specific materials, which endow them with outstanding physical properties, enabling their application in a wide range of scenarios. -
Dead end Guy Grip
Dead-end preformed is widely used for the installation of bare conductors or overhead insulated conductors for transmission and distribution lines. The reliability and economic performance of the product are better than the bolt type and hydraulic type tension clamp that are widely used in the current circuit. This unique, one-piece dead-end is neat in appearance and free from bolts or high-stress holding devices. It can be made of galvanized steel or aluminum clad steel. -
Module OYI-1L311xF
OYI-1L311xF Small Form Factor Pluggable (SFP) transceivers are compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA), The transceiver consists of five sections: the LD driver, the limiting amplifier, the digital diagnostic monitor, the FP laser and the PIN photo-detector, the module data link up to 10km in 9/125um single mode fiber. The optical output can be disabled by a TTL logic high-level input of Tx Disable, and the system also 02 can disable the module via I2C. Tx Fault is provided to indicate that degradation of the laser. Loss of signal (LOS) output is provided to indicate the loss of an input optical signal of receiver or the link status with partner. The system can also get the LOS (or Link)/Disable/Fault information via I2C register access. -
FTTH Pre-Connectorized Drop Patchcord
Pre-Connectorized Drop cable is over the ground fiber optic drop cable equipped with fabricated connector on both ends, packed in certain length, and used for distributing optical signal from Optical Distribution Point (ODP) to Optical Termination Premise (OTP) in customer’s House. According to the transmission medium, it divides to Single Mode and Multi Mode Fiber Optic Pigtail; According to the connector structure type, it divides FC, SC, ST, MU, MTRJ, D4, E2000, LC etc.; According to the polished ceramic end-face, it divides to PC, UPC and APC. Oyi can provide all kinds of optic fiber patchcord products; The transmission mode, optical cable type and connector type can be arbitrarily matched. It has the advantages of stable transmission, high reliability and customization; it is widely used in optical network scenarios such as FTTX and LAN etc.
If you're looking for a reliable, high-speed fibre optic cable solution, look no further than OYI. Contact us now to see how we can help you stay connected and take your business to the next level.
