0755-23179541 
sales@oyii.net.png)
8618926041961
OYI-F504
Optical Distribution Frame
OYI-F504
Product Features
1.Comply with ANSI/EIA RS-310-D, DIN 41497 Part-1, IEC297-2, DIN41494 Part 7, GBIT3047.2-92 standard.
2.19” telecommunication and data rack specially designed for easy hassle, free installations of Optical Distribution Frame (ODF) and patch panels.
3.Top and bottom entry with plate with corrosion resistant fringe fit grommet.
4.Fitted with quick release side panels with spring fit.
5.Vertical patch cord management bar/ cable clips/ bunny clips/ cable management rings/ Velcro cable management.
6.Split type Front door access.
7.Cable management slotting rails.
8.Aperture dust resistant front panel with top and bottom locking knob.
9.M730 press fit pressure sustain locking system.
10.Cable entry unit top/ bottom.
11.Designed for Telecom central exchange applications.
12.Surge protection Earthling bar.
13.Load capacity 1000 KG.
Technical Specifications
1.Standard
Compliance with YD/T 778- Optical Distribution Frames.
2. Inflammability
Compliance with GB5169.7 Experiment A.
3. Environmental Conditions
Operation temperature: -5°C ~+40°C
Storage and transportation temperature: -25°C ~+55°C
Relative humidity: ≤85% (+30°C)
Atmospheric pressure: 70 Kpa ~ 106 Kpa
Features
1.Closed sheet-metal structure, operable both on front/ rear side, Rack-mount,19’’ (483mm).
2.Supporting Suitable module, high density, large capacity, saving space of equipment room.
3.Independent lead-in/out of optical cables, pigtails and patch cords.
4.Layered fiber across unit, facilitating patch cord management.
5.Optional fiber hanging assembly, double rear door and rear door panel.
Dimension
2200 mm (H) × 800 mm (W) × 300 mm (D) (Figure 1)
Figure 1
Partial Configuration
Packaging Information
|
Model
|
Dimension
H × W × D(mm) (Without package) |
Configurable capacity (termination/ splice) |
Net weight (kg)
|
Gross weight (kg)
|
Remark
|
|
OYI-504 Optical Distribution Frame
|
2200×800×300
|
720/720
|
93
|
143
|
Basic rack, including all accessories and fixings, excluding patch panels etc
|
-
16 Cores Type OYI-FAT16B Terminal Box
The 16-core OYI-FAT16B optical terminal box performs in accordance with the industry standard requirements of YD/T2150-2010. It is mainly used in the FTTX access system terminal link. The box is made of high-strength PC, ABS plastic alloy injection molding, which provides good sealing and aging resistance. In addition, it can be hung on the wall outdoors or indoors for installation and use. The OYI-FAT16B optical terminal box has an inner design with a single-layer structure, divided into the distribution line area, outdoor cable insertion, fiber splicing tray, and FTTH drop optical cable storage. The fiber optical lines are very clear, making it convenient to operate and maintain. There are 2 cable holes under the box that can accommodate 2 outdoor optical cables for direct or different junctions, and it can also accommodate 16 FTTH drop optical cables for end connections. The fiber splicing tray uses a flip form and can be configured with 16 cores capacity specifications to accommodate the box’s expansion needs. -
All Dielectric Self-Supporting Cable
The structure of ADSS (single-sheath stranded type) is to place 250um optical fiber into a loose tube made of PBT, which is then filled with waterproof compound. The center of the cable core is a non-metallic central reinforcement made of fiber-reinforced composite (FRP). The loose tubes (and filler rope) are twisted around the central reinforcing core. The seam barrier in the relay core is filled with water-blocking filler, and a layer of waterproof tape is extruded outside the cable core. Rayon yarn is then used, followed by extruded polyethylene (PE) sheath into the cable. It is covered with a thin polyethylene (PE) inner sheath. After a stranded layer of aramid yarns is applied over the inner sheath as a strength member, the cable is completed with a PE or AT (anti-tracking) outer sheath. -
OPGW Optical Ground Wire
Layered stranded OPGW is one or more fiber-optic stainless steel units and aluminum-clad steel wires together, with stranded technology to fix the cable, aluminum-clad steel wire stranded layers of more than two layers, the product features can accommodate multiple fiber-optic unit tubes, fiber core capacity is large. At the same time, the cable diameter is relatively large, and the electrical and mechanical properties are better. The product features light weight, small cable diameter and easy installation. -
Anchoring Clamp PA300
The anchoring cable clamp is a high-quality and durable product. It consists of two parts: a stainless-steel wire and a reinforced nylon body made of plastic. The body of the clamp is made of UV plastic, which is friendly and safe to use even in tropical environments. The FTTH anchor clamp is designed to fit various ADSS cable designs and can hold cables with diameters of 4-7mm. It is used on dead-end fiber optic cables. Installing the FTTH drop cable fitting is easy, but preparation of the optical cable is required before attaching it. The open hook self-locking construction makes installation on fiber poles easier. The anchor FTTX optical fiber clamp and drop wire cable brackets are available either separately or together as an assembly. FTTX drop cable anchor clamps have passed tensile tests and have been tested in temperatures ranging from -40 to 60 degrees. They have also undergone temperature cycling tests, aging tests, and corrosion-resistant tests. -
310GR
ONU product is the terminal equipment of a series of XPON which comply fully with ITU-G.984.1/2/3/4 standard and meet the energy-saving of G.987.3 protocol, is based on mature and stable and high cost-effective GPON technology which adopts high-performance XPON Realtek chipset and has high reliability, easy management, flexible configuration, robustness, good quality service guarantee (Qos).XPON has G / E PON mutual conversion function, which is realized by pure software. -
Drop Cable Anchoring Clamp S-Type
Drop wire tension clamp s-type, also called FTTH drop s-clamp, is developed to tension and support flat or round fiber optic cable on intermediate routes or last mile connections during outdoor overhead FTTH deployment. It is made of UV proof plastic and a stainless steel wire loop processed by injection molding technology.
If you're looking for a reliable, high-speed fibre optic cable solution, look no further than OYI. Contact us now to see how we can help you stay connected and take your business to the next level.
