0755-23179541 
sales@oyii.net
OYI-ODF-SR2-Series Type
Optic Fiber Terminal/Distribution Panel
OYI-ODF-SR2-Series Type
Product Features
19" standard size , easy install.
Install with sliding rail, and front cable management plate easy for take out.
Light weight, strong strength, good anti-shocking and dustproof.
Well cable management, cable can be distinguished easily.
Roomy space ensure fiber bent ratio.
All types pigtail available for installation.
Use of cold-rolled steel sheet with strong adhesive force, artistic design, and durability.
Cable entrances are sealed with oil-resistant NBR to increase flexibility. Users can choose to pierce the entrance and exit.
Versatile panel with extendable double slide rails for smooth sliding.
Comprehensive accessory kit for cable entry and fiber management.
Patch cord bend radius guides minimize macro bending.
Full assembly (loaded) or empty panel.
Different adapter interface including ST, SC, FC, LC,E2000 etc.
Splice capability is up to Max. 48 fibers with splice trays loaded.
Fully compliant with YD/T925—1997 quality management system.
Operations
Peel the cable, remove the outer and inner housing, as well as any loose tube, and wash off the filling gel, leaving 1.1 to 1.6m of fiber and 20 to 40mm of steel core.
Attach the cable-pressing card to the cable, as well as the cable reinforce steel core.
Guide the fiber into the splicing and connecting tray, secure the heat-shrink tube and splicing tube to one of the connecting fibers. After splicing and connecting the fiber, move the heat-shrink tube and splicing tube and secure the stainless (or quartz) reinforce core member, ensuring that the connecting point is in the middle of the housing pipe. Heat the pipe to fuse the two together. Place the protected joint into the fiber-splicing tray. (One tray can accommodate 12-24 cores)
Lay the remaining fiber evenly in the splicing and connecting tray, and secure the winding fiber with nylon ties. Use the trays from the bottom up. Once all the fibers have been connected, cover the top layer and secure it.
Position it and use the earth wire according to the project plan.
Packing List:
(1)Terminal case main body: 1 piece
(2)Polishing sand paper: 1 piece
(3)Splicing and connecting mark: 1 piece
(4)Heat shrinkable sleeve: 2 to 144 pieces, tie: 4 to 24 pieces
Specifications
|
Mode Type |
Size (mm) |
Max Capacity |
Outer Carton Size (mm) |
Gross Weight (kg) |
Quantity In Carton Pcs |
|
OYI-ODF-SR2-1U |
482*300*1U |
24 |
540*330*285 |
17.5 |
5 |
|
OYI-ODF-SR2-2U |
482*300*2U |
72 |
540*330*520 |
22 |
5 |
|
OYI-ODF-SR2-3U |
482*300*3U |
96 |
540*345*625 |
18.5 |
3 |
|
OYI-ODF-SR2-4U |
482*300*4U |
144 |
540*345*420 |
16 |
2 |
Applications
Data communications networks.
Storage area network.
Fiber channel.
FTTx system wide area network.
Test instruments.
CATV networks.
Widely used in FTTH access network.
Packaging Information
Inner Packaging
Outer Carton
-
8 Cores Type OYI-FAT08E Terminal Box
The 8-core OYI-FAT08E optical terminal box performs in accordance with the industry standard requirements of YD/T2150-2010. It is mainly used in the FTTX access system terminal link. The box is made of high-strength PC, ABS plastic alloy injection molding, which provides good sealing and aging resistance. In addition, it can be hung on the wall outdoors or indoors for installation and use.
The OYI-FAT08E optical terminal box has an inner design with a single-layer structure, divided into the distribution line area, outdoor cable insertion, fiber splicing tray, and FTTH drop optical cable storage. The fiber optical lines are very clear, making it convenient to operate and maintain. It can accommodate 8 FTTH drop optical cables for end connections. The fiber splicing tray uses a flip form and can be configured with 8 cores capacity specifications to meet the expansion needs of the box.
-
Self-supporting Figure 8 Fiber Optic Cable
The 250um fibers are positioned in a loose tube made of high modulus plastic. The tubes are filled with a water-resistant filling compound. A steel wire is located in the center of the core as a metallic strength member. The tubes (and fibers) are stranded around the strength member into a compact and circular cable core. After an Aluminum (or steel tape) Polyethylene Laminate (APL) moisture barrier is applied around the cable core, this part of the cable, accompanied by the stranded wires as the supporting part, is completed with a polyethylene (PE) sheath to form a figure 8 structure. Figure 8 cables, GYTC8A and GYTC8S, are also available upon request. This type of cable is specifically designed for self-supporting aerial installation.
-
Zipcord Interconnect Cable GJFJ8V
ZCC Zipcord Interconnect Cable uses 900um or 600um flame-retardant tight buffer fiber as an optical communication medium. The tight buffer fiber is wrapped with a layer of aramid yarn as strength member units, and the cable is completed with a figure 8 PVC, OFNP, or LSZH (Low Smoke, Zero Halogen, Flame-retardant) jacket.
-
24-48Port, 1RUI2RUCable Management Bar Included
1U 24 Ports（2u 48） Cat6 UTP Punch Down Patch Panel for 10/100/1000Base-T and 10GBase-T Ethernet. The 24-48 port Cat6 patch panel shall terminate 4-pair, 22-26 AWG, 100 ohm unshielded twisted pair cable with 110 punch down termination, which is color-coded for T568A/B wiring, providing the perfect 1G/10G-T speed solution for PoE/PoE+ applications and any voice or LAN application.
For hassle-free connections, this Ethernet patch panel offers straight Cat6 ports with 110-type termination, making it easy to insert and remove your cables. The clear numbering on the front and back of the network patch panel enables quick and easy identification of cable runs for efficient system management. Included cable ties and a removable cable management bar help organize your connections, cut down on cord clutter, and maintain stable performance.
-
SC/APC SM 0.9mm Pigtail
Fiber optic pigtails provide a quick way to create communication devices in the field. They are designed, manufactured, and tested according to protocols and performance standards set by the industry, which will meet your most stringent mechanical and performance specifications.
A fiber optic pigtail is a length of fiber cable with only one connector fixed on one end. Depending on the transmission medium, it is divided into single mode and multi mode fiber optic pigtails; according to the connector structure type, it is divided into FC, SC, ST, MU, MTRJ, D4, E2000, LC, etc. according to the polished ceramic end-face, it is divided into PC, UPC, and APC.
Oyi can provide all kinds of optic fiber pigtail products; the transmission mode, optical cable type, and connector type can be arbitrarily matched. It has the advantages of stable transmission, high reliability, and customization, it is widely used in optical network scenarios such as central offices, FTTX, and LAN, etc.
-
Fanout Multi-core (4~48F) 2.0mm Connectors Patc...
OYI fiber optic fanout patch cord, also known as a fiber optic jumper, is composed of a fiber optic cable terminated with different connectors on each end. Fiber optic patch cables are used in two major application areas: computer workstations to outlets and patch panels or optical cross-connect distribution centers. OYI provides various types of fiber optic patch cables, including single-mode, multi-mode, multi-core, armored patch cables, as well as fiber optic pigtails and other special patch cables. For most patch cables, connectors such as SC, ST, FC, LC, MU, MTRJ, and E2000 (APC/UPC polish) are all available.
If you're looking for a reliable, high-speed fibre optic cable solution, look no further than OYI. Contact us now to see how we can help you stay connected and take your business to the next level.